@article { author = {Tabatabaee, F. and Khorasani, M. and Ebrahimi, M. and González, A. and Irusta, L. and Sardon, H.}, title = {Effect of Siloxane Crosslinking on Colloidal, Mechanical, and Thermal Properties of Self-curable Waterborne Polyurethane Dispersions}, journal = {Journal of Color Science and Technology}, volume = {13}, number = {4}, pages = {267-276}, year = {2020}, publisher = {Institute for Color Science and Technology with scientific cooperation of Iran Color Society}, issn = {1735-8779}, eissn = {2383-2169}, doi = {}, abstract = {Self-curable waterborne polyurethane (WPU) dispersions were prepared via acetone process. The effects of (3-aminopropyl) triethoxysilane (APTES) content as crosslinking agent on the properties of WPUs were investigated. To confirm the polymer structure and the presence of alkoxysilane groups, 1H nuclear magnetic resonance and fourier transform infrared spectroscopy were used. Gel content of the sample containing 10 wt% APTES was reported 90.5% which were revealed highly crosslinking network of the WPU film. Although the particle size went up from 36.5 to 63 nm by introducing 10 wt% APTES, narrow particle size distributions (PDI < 0.2) and the absolute value of zeta potentials greater than 40 mV were obtained. Furtheremore, atomic force microscopy showed that the introduction of siloxane crosslinking increased microphase-separation of the polyurethane films. In the presence of 10 wt% APTES, excellent enhancement in water resistance (water absorption < 5%), mechanical properties (Young’s modulus=420 MPa and tensile strength=46.7 MPa), and thermal stability (Tmax1=321 ºC and Tmax2=407 ºC) made this type of crosslinking highly suitable for WPUs in coating applications. }, keywords = {Waterborne polyurethane,Dispersions,Self-curable,Alkoxysilane groups}, title_fa = {اثر حضور پیوندهای عرضی سیلوکسانی بر خواص کلوئیدی، مکانیکی و حرارتی پراکنه‌های پلی‌یورتان آب پایه خود شبکه‌ای شونده}, abstract_fa = {در پژوهش حاضر، پراکنه‌های پلی‌یورتان آب پایه خود شبکه‌ای شونده در دمای محیط به روش ‌فرآیند استن ساخته شدند. اثر حضور غلظت‌های مختلف از 3-(آمینوپروپیل)تری‌اتوکسی‌سیلان به عنوان عامل اتصال‌دهنده عرضی مطالعه شد. جهت بررسی ساختار شیمیایی و حضور گروه‌های آلکوکسی سیلان از آزمون‌های رزونانس مغناطیسی هسته پروتون و طیف‌سنجی فوریه زیر قرمز استفاده شد. محتوای ژل نمونه حاوی wt%10از عامل سیلانی، 90.5% گزارش شد که تاییدی بر تشکیل ساختار به شدت شبکه‌ای سیلوکسانی بود. با وجود افزایش در اندازه ذرات پلی‌یورتان از 36.5 به ۶۳ نانومتر در غیاب و حضور wt%10از عامل سیلانی، توزیع باریک در اندازه ذرات پلی‌یورتان (0.2>PDI) و مقادیر مطلق پتانسیل‌ زتای بالای mV 40، پایداری کلوئیدی بالای این پراکنه‌ها را نشان داد. افزایش جدایش میکرو فازی در نمونه‌های شبکه‌ای شده توسط آزمون میکروسکوپ نیروی اتمی مشاهده شد. بهبود چشمگیر در مقاومت آبی (جذب آب < 5%)، خواص مکانیکی (مدول یانگMPa 420و استحکام کششی MPa 46.7) و پایداری حرارتی (ºC321= Tmax1و ºC407=Tmax2) پلی‌یورتان آب‌پایه حاوی wt%10از عامل سیلانی، نشانگر عملکرد عالی اتصال‌دهنده عرضی سیلانی در ساخت پوشش‌های آب پایه پلی‌یورتانی است.  }, keywords_fa = {پلی‌یورتان آب‌پایه,پراکنه‌ها,خود شبکه‌ای شونده,آلکوکسی سیلان‌ها}, url = {https://jcst.icrc.ac.ir/article_81548.html}, eprint = {https://jcst.icrc.ac.ir/article_81548_1f5889089d7291843b55eaa3f4be538e.pdf} } @article { author = {Ramezani Charmineh, A. and Azadi Boyaghchi, M. and Zolfaghari, B.}, title = {Investigating the Impact of Absinthium Additive on Stabilization of Color of Iron-Gall Ink}, journal = {Journal of Color Science and Technology}, volume = {13}, number = {4}, pages = {277-291}, year = {2020}, publisher = {Institute for Color Science and Technology with scientific cooperation of Iran Color Society}, issn = {1735-8779}, eissn = {2383-2169}, doi = {}, abstract = {Iron-gall ink is one of the varieties of inks used in the past that consists of four main components of gall nut, vitriol, gum arabic and water and due to chemical instability changes color over time. The present study tried to investigate the impact of the extract of absinthium, as well as the ratio of gall to the alum used in the manufacture of ink on stabilization of the color of iron-gall ink based on old references and through laboratory studies. In this study, after making two types of black ink using old sources, the samples were exposed to light and temperature-humidity aging and after examination by using acidity and colorimetric tests, it was determined that adding extracts of Artemisia absinthium to iron-gall ink can stabilize its color, and the ratio of gall to alum is also an important factor in this sustainability. }, keywords = {Extract,Artemisia absinthium,Stabilization,Iron-gall ink}, title_fa = {بررسی تأثیر افزودنی اَفسَنتین بر ثبات ‏رنگ مرکب آهن- مازو}, abstract_fa = {مرکب آهن-مازو یکی از انواع مرکب‌های به کار رفته در گذشته است که از چهار جز اصلی مازو، زاج، صمغ عربی و آب تشکیل شده است و به دلیل ناپایداری شیمیایی، با گذر زمان دچار تغییر رنگ می‌شود. آنچه در این پژوهش مورد کنکاش قرار می‏گیرد بررسی تأثیر عصاره اَفسَنتین و همچنین نسبت مازو به زاج مورد استفاده در ساخت مرکب بر پایدارسازی رنگ مرکب آهن- مازو به استناد منابع قدیم و مطالعات آزمایشگاهی است. در این پژوهش پس از ساخت دو نوع مرکب مشکی با استفاده از منابع کهن، نمونه‌ها تحت پیرسازی نوری و دما- رطوبت قرار گرفت و پس از بررسی با استفاده از آزمون‌های تعیین میزان اسیدیته و رنگ‌سنجی، مشخص شد که افزودن عصاره گیاه آرتمیزیا آبسینتیوم به مرکب آهن- مازو سبب پایدارسازی رنگ آن می‌شود و نسبت مازو به زاج نیز عامل مهمی در این پایداری به شمار می‌‏رود.}, keywords_fa = {عصاره,اَفسَنتین,پایدارسازی,مرکب آهن- مازو}, url = {https://jcst.icrc.ac.ir/article_81582.html}, eprint = {https://jcst.icrc.ac.ir/article_81582_41c943769e6787949149f62ec978cee5.pdf} } @article { author = {Mujodi, F. and Mohammadi Achachluei, M. and Alihosseini, F.}, title = {Comparative Study of FTIR (Fourier Transform Infrared Spectroscopy) and TLC (Thin Layer Chromatography) Efficiency for Application in Identification of Kermes Dye on Historical Fibers}, journal = {Journal of Color Science and Technology}, volume = {13}, number = {4}, pages = {293-303}, year = {2020}, publisher = {Institute for Color Science and Technology with scientific cooperation of Iran Color Society}, issn = {1735-8779}, eissn = {2383-2169}, doi = {}, abstract = {The aim of this research was study and comparison of FT-IR and TLC results for characterization of kermes dyes in archaeological and historical fibers and assessment of their advantages and disadvantages. Samples were prepared from silk and wool fibers. The samples were artificially aged according to Feller (1994). After aging, color change and pH were measured. Fourie Transform Infrared Spectroscopy-Attenuated Total Reflectance (ATR-FTIR) was applied for assessment and comparison of aged and unaged samples. Moreover, Thin Layer Chromatography was used before and after aging by choosing appropriate solvent. Results showed after aging, pH content of dyed silk with kermes was increased and Rf in TLC indicated minor change. The ATR-FTIR spectometer results showed that there are no differences between raw and dyed fibers, therefore, the color should be extracted in order to specify the sepctrum of color ingredients. After extarcting the samples, they do not differ much with the aged ones.}, keywords = {Dye,kermes,Fourie Transform Infrared Spectroscopy Total Reflectance (FTIR),Thin Layer Chromatography (TLC)}, title_fa = {بررسی تطبیقی کارایی روش‌های طیف‌سنجی زیر قرمز تبدیل فوریه (FTIR) و کروماتوگرافی لایه نازک (TLC) جهت کاربرد در شناسایی ماده رنگزای قرمزدانه در الیاف تاریخی}, abstract_fa = {هدف این تحقیق بررسی تطبیقی نتایج روش های FTIR و TLC در شناسایی ماده رنگزای قرمزدانه در الیاف تاریخی – باستان شناختی و بررسی معایب و مزایای آنها است. ابتدا نمونه‌هایآماده شده تحت پیرسازی دما، طبق نظریه فلر 1994 قرارگرفتند و تغییرات فام و pH آنها بررسی شد. برای بررسی تغییرات قبل و بعد از پیرسازی، (ATR-FTIR) و بعد از استخراج ماده رنگزا، TLC انجام شد. نتایج نشان داد، pH ابریشم رنگرزی شده با قرمزدانه افزایش یافته‌است و کمترین میزان تغییرات Rf در محاسبه مربوط به TLC را دارد و نتایج طیف‌سنجی  ATR-FTIRنشان داد، در مقایسه الیاف خام، رنگرزی شده و پیر‌سازی شده این مطلب مشهود است که تفاوتی بین لیف خام و لیف رنگرزی شده وجود ندارد لذا بایستی استخراج صورت گیرد تا طیف مربوط به اجزا ماده رنگزا مشخص گردد.}, keywords_fa = {ماده رنگزا,قرمزدانه,طیف‌سنجی مادون قرمز تبدیل فوریه,کروماتوگرافی لایه نازک}, url = {https://jcst.icrc.ac.ir/article_81584.html}, eprint = {https://jcst.icrc.ac.ir/article_81584_d03e27b63ece67477063b09e0373cc53.pdf} } @article { author = {Abedini, E. and Baniasad, Sh.}, title = {The Effect of Potassium Oxalate and Nickel Oxide as Additives on The Structure, Corrosion Resistance and Abrasion Properties of Manganese Phosphate Coating}, journal = {Journal of Color Science and Technology}, volume = {13}, number = {4}, pages = {305-315}, year = {2020}, publisher = {Institute for Color Science and Technology with scientific cooperation of Iran Color Society}, issn = {1735-8779}, eissn = {2383-2169}, doi = {}, abstract = {During this research, the formulation of manganese phosphate bath was designed to create layers on the surface of low carbon steel alloys (St 37) to enhance corrosion, abrasion and friction resistance. At the first, a basic solution of the manganese phosphate bath was prepared by optimizing the concentration of each components of the bath. Then, the effects of potassium oxalate and nickel oxide additives on coating properties such as thickness, unit weight of surface (With optimal value of 1± 0.1 gr/l nickel oxide, the weight of the coating 39.8 ± 0.2 gr/m was obtained and optimal value of 0.5±0.1 gr/l potassium oxalate, the weight of the coating 48.99±0.3 gr/m2 was obtained), morphology, corrosion and abrasion resistance were investigated and finally, the best coating determined.The results of various experiments showed that the major phase of manganese phosphate coating is Hureaulite, which is in the form of cubic crystals in the basic solution that does not contain any additives, of course, with the addition of additives, the shape of the crystals is changed and the particle size becomes smaller and denser. The highest corrosion resistance obtained during the salt spray test (98 hours) and electrochemical impedance spectroscopy (EIS) (with Polarization 77983±253) is related to phosphate coating containing nickel oxide. According to the results of the Pin on disk test the specimens which were phosphated and soaped reduced the coefficient of surface friction from about 0.6 (for uncoated steel) to about 0.15, and this indicated the anti-abrasion and friction properties of these coatings.}, keywords = {Manganese phosphate,Additives,potassium oxalate,Nickel Oxide,Hureaulite,Corrosion and abrasion resistance}, title_fa = {تاثیر افزودنی اگزالات پتاسیم و اکسید نیکل بر ساختار، مقاومت خوردگی و سایش پوشش فسفات منگنز}, abstract_fa = {در این تحقیق، فرمول‌بندی حمام فسفات منگنز به‌منظور ایجاد لایه‏ای مقاوم در برابر خوردگی، سایش و اصطکاک بر روی سطح فولاد کم‌کربن (St37) مورد بررسی قرار گرفت. به این منظور ابتدا محلول پایه فسفات منگنز با بهینه‌سازی غلظت هرکدام از اجزا سازنده حمام، تهیه شد. سپس اثر افزودنی‏های اگزالات پتاسیم و اکسید نیکل بر روی خواص پوشش نظیر ضخامت، وزن واحد سطح (با مقدار بهینه gr/l 0.1 ±1 اکسید نیکل وزن پوشش مقدار gr/m20.2± 39.8 و با مقدار بهینه gr/l 0.1 ± 0.5اگزالات پتاسیم وزن پوشش مقدار gr/m2 0.3± 48.99 گردید.)، ریخت‌شناسی، مقاومت به خوردگی و سایش بررسی گردید و درنهایت بهترین پوشش‏ها مشخص شد. نتایج آزمون‏های مختلف نشان داد که فاز عمده‏ پوشش فسفات منگنز، هوراولیت می‏باشد که در پوشش‏های حاصل از محلول فاقد هرگونه افزودنی، شکل بلورها، به‌صورت مکعب می‏باشد، که البته با اضافه کردن افزودنی‌ها شکل بلورها تغییر ‏کرده و اندازه ذرات نیز ریزتر و فشرده‏تر می‏گردد. بالاترین مقاومت خوردگی به‌دست‌آمده تحت آزمون مه نمکی (98 ساعت) و طیف‏سنجی امپدانس الکتروشیمیایی (EIS) ( با مقاومت انتقال بار (Rp) Ω.cm2253± 77983)مربوط به پوشش فسفات حاوی اکسید نیکل می‏باشد. مطابق نتایج حاصل از آزمون پین روی صفحه (Pin on disk)نمونه‏های فسفاته و صابونی شده، ضریب اصطکاک سطح را از حدود 0.6 (برای فولاد بدون پوشش) به حدود 0.15 کاهش داده، که این مسئله نشان‏دهنده‏ خاصیت ضد سایش و اصطکاک این پوشش‏ها می‏باشد.}, keywords_fa = {فسفات منگنز,افزودنی‏ها,اگزالات پتاسیم,اکسید نیکل,هوراولیت,مقاومت در برابر خوردگی و سایش}, url = {https://jcst.icrc.ac.ir/article_81585.html}, eprint = {https://jcst.icrc.ac.ir/article_81585_57607767a79868f5c6c779b3a43b758a.pdf} } @article { author = {Zamani, S. and Salem, Sh.}, title = {Simultaneous Application of Graphene Oxide and CNT for Photocatalytic Activity Improvement of TiO2}, journal = {Journal of Color Science and Technology}, volume = {13}, number = {4}, pages = {317-330}, year = {2020}, publisher = {Institute for Color Science and Technology with scientific cooperation of Iran Color Society}, issn = {1735-8779}, eissn = {2383-2169}, doi = {}, abstract = {Synthesis of TiO2- based composite by using carbonous materials can solve some restrictions related to the application of titanium dioxide in industrial scale. In this study carbon nanotubes (CNTs), graphene oxide (GO) and reduced graphene oxide (RGO) are used to improve the photocatalytic activity of TiO2 for the degradation of methylene blue under visible light irradiation and the effect of simultaneous usage of graphene sheets and CNTs are evaluated through the enhancement of TiO2 degradation activity. The photocatalytic activity and characterization of as-prepared samples were evaluated by Fourier transform-infrared spectroscopy, X-ray diffraction, Field emission scanning electron microscopy and UV-Vis Spectrophotometer. Results indicate the successful preparationof TiO2-CNT-GO nanocomposite by sol-gel method. Moreover the simultaneous using of graphene sheets and CNT can prove the composite decoloration activity. The maximum photocatalytic degradation of MB (94%) is achieved within 90 min. The enhanced photocatalytic activity of TiO2-CNT-GO nanocomposite can be ascribed to the high surface area, severe electron transmission and monotone distribution of carbon based nanoparticles.}, keywords = {Titanium dioxide,Carbon Nanotube,graphene oxide,Nanocomposite,Methylene blue,Visible light}, title_fa = {بررسی تأثیر استفاده هم‌زمان از نانولوله کربنی و اکسید گرافن در بهبود فعالیت کاتالیزوری نوری TiO2}, abstract_fa = {استفاده از دی‌اکسید تیتانیم در فرآیندهای تصفیه نیازمند به کارگیری روش‌هایی همچون استفاده از مواد کربنی و ساخت کامپوزیت جهت بهبود عملکرد این ماده است. در پژوهش حاضر از نانولوله کربنی (CNT)، اکسید گرافن (GO) و اکسید گرافن کاهش یافته (RGO) به منظور بهبود عملکرد TiO2 در حذف متیلن‌آبی تحت تابش نور مرئی، استفاده شده و تاثیر استفاده هم‌زمان از ورقه‌های گرافنی و CNT در افزایش فعالیت TiO2 مطالعه شده است. ساختار و عملکرد نانوکامپوزیت سنتز شده توسط طیف‌سنج زیرقرمز، پراش پرتو ایکس، میکروسکوپ الکترونی روبشی و طیف‌سنج فرابنفش- مرئی مورد ارزیابی قرار گرفته است. نتایج حاصل نشان می‌دهد که با استفاده از روش سل-ژل امکان سنتز ترکیب سه‌تایی TiO2-GO-CNT وجود داشته و استفاده هم‌زمان از ورقه‌های گرافنی و CNT در ساخت کامپوزیت، عملکرد مناسبی برای رنگ‌زدایی به همراه داشته است به طوری که پس از90 دقیقه، حذف 94% از متیلن آبی گزارش شده است. افزایش سطح، انتقال سریع الکترون‌ها و پراکندگی یکنواخت مواد کربنی می‌تواند از جمله دلایل بهبود عملکرد کاتالیزور نوری کامپوزیت TiO2-GO-CNT باشد.}, keywords_fa = {دی‌اکسید تیتانیم,نانولوله کربنی,اکسید گرافن,نانوکامپوزیت,متیلن آبی,نور مرئی}, url = {https://jcst.icrc.ac.ir/article_81587.html}, eprint = {https://jcst.icrc.ac.ir/article_81587_cb9ddbb361b2846400985637a63c9a08.pdf} } @article { author = {Nematian, B. and Ramazani S.A., A. and Mahdavian, M. and Bahlakeh, Gh. and Haddadi, S. A.}, title = {Investigation the Effect of Safflower Extract as a Green Inhibitor for Corrosion Inhibition of Mild Steel in 0.1 M HCl Solution}, journal = {Journal of Color Science and Technology}, volume = {13}, number = {4}, pages = {331-340}, year = {2020}, publisher = {Institute for Color Science and Technology with scientific cooperation of Iran Color Society}, issn = {1735-8779}, eissn = {2383-2169}, doi = {}, abstract = {In this research, safflower extract was used as a green inhibitor in 0.1 M HCl solution to evaluate the rate of corrosion of mild steel in this environment. At the first step, the extract of fresh safflower plant (SPE) was prepared. The chemical structure of SPE was recognized by Fourier Transform Infrared Spectroscopy (FTIR). At the second step the solution of 0.1 M HCl containing 500 ppm SPE was prepared and in the next step the corrosion inhibition performances of the extract solution were proved by means of electrochemical impedance spectroscopy (EIS) technique and potentiodynamic polarization measurement then the result of these analyses was compared to the result of the dipped mild steel sample in the 0.1 M HCl solution without inhibitor. The morphology of the mild steel surface immersed in the extract solutions was evaluated by scanning electron microscopy (FE-SEM). According to the EIS results, the significant increment was observed in corrosion inhibition of acidic solution containing SPE in comparison with Blank solution. The result of potentiodynamic polarization measurement showed this green inhibitor acted as a mixed type inhibitor.}, keywords = {Green corrosion inhibitor,Mild steel,Anti-corrosion,Safflower plant}, title_fa = {بررسی اثر عصاره گیاه گلرنگ به عنوان یک بازدارنده خوردگی سبز جهت جلوگیری از خوردگی فولاد نرم در محیط اسید کلریدریک 0.1 مولار}, abstract_fa = {در این پژوهش، عصاره گیاه گلرنگ به عنوان بازدارنده سبز در محیط خورنده اسید کلریدریک 0.1 مولار استفاده شد تا میزان کاهش خوردگی فلز نرم در این محیط بررسی گردد. در گام نخست، از گیاه تازه گلرنگ عصاره تهیه شد. ترکیبات موجود در گیاه گلرنگ توسط آزمون تبدیل فوریه طیف‌سنجی زیر قرمز (FT-IR) شناسایی شد. سپس محلول اسید کلریدریک 0.1 مولار حاوی ppm 500 از عصاره گیاه گلرنگ تهیه شد. در مرحله بعد، میزان خوردگی فلز نرم غوطه‌ور شده در این محلول طی زمان توسط آزمون‌های طیف‌نگاری امپدانس الکتروشیمیایی (EIS) و پلاریزاسیون مورد بررسی قرار گرفت و نتایج آنها با نتایج حاصل از فلز غوطه‌ور شده در محلول اسید کلریدریک 0.1 مولار در عدم حضور بازدارنده مقایسه شد. ریخت‌شناسی سطح فولاد‌های غوطه‌ور شده توسط آزمون میکروسکوپ الکترونی روبشی انتشار میدانی (FE-SEM-EDX) مورد بررسی قرار گرفت. نتایج حاصل از آزمون EIS حاکی از آن بود که اضافه کردن ppm 500 از بازدارنده سبز گلرنگ به محلول اسید کلریدریک 0.1 مولار باعث افزایش چشم‌گیری در میزان مقاومت خوردگی فولاد نرم در مقایسه با نمونه شاهد شد. نتایج آزمون پلاریزاسیون نشان داد سازوکار عملکرد بازدارنده به صورت مخلوط می‌باشد.}, keywords_fa = {بازدارنده خوردگی سبز,فولاد نرم,ضدخوردگی,گیاه گلرنگ}, url = {https://jcst.icrc.ac.ir/article_81588.html}, eprint = {https://jcst.icrc.ac.ir/article_81588_503adb8346c2a919d3136eac0561f10c.pdf} } @article { author = {Javidparvar, A. A. and أaderi, R. and Ramezanzadeh, B.}, title = {Incorporation of Graphene Oxide Nanoparticles Modified with Benzimidazole into an Epoxy Polyamide Coating to Enhance the Physical-Mechanical Properties}, journal = {Journal of Color Science and Technology}, volume = {13}, number = {4}, pages = {341-352}, year = {2020}, publisher = {Institute for Color Science and Technology with scientific cooperation of Iran Color Society}, issn = {1735-8779}, eissn = {2383-2169}, doi = {}, abstract = {In this paper, the graphene oxide nanosheets modified by benzimidazole were used as the epoxy coating reinforcing nanoparticles. In this way, after synthesizing of graphene oxide and physically adsorption of benzimidazole molecules on them, the modified graphene oxide nanosheets and the unmodified graphene oxide were dispersed in the epoxy matrix. The physical-mechanical properties of the coatings obtained were evaluated by DMTA and tensile tests. In addition, by a scanning electron microscope (SEM) the coating fractured surface morphology and the degree of nanoparticle dispersion in the coatings were studied. The results showed that the benzimidazole molecules could successfully modify the graphene oxide nanosheets surface via noncovalent bonds. Furthermore, the ultimate tensile strength, Young's modulus, strain at break, and energy at break were increased 81%, 15%, 310%, and 207%, respectively, compared to the neat epoxy coating. This improvement in physical-mechanical properties of the coating may be attributed to the better dispersion of the nanosheets in the coating as well as the stronger interactions between the nanosheets and the epoxy resin.}, keywords = {Epoxy polyamide coating,Graphene oxide nanosheets,Benzimidazole,Physical-mechanical properties}, title_fa = {بکارگیری نانوذرات اکسید گرافن اصلاح سطحی شده توسط بنزایمیدازول جهت بهبود خواص فیزیکی-مکانیکی پوشش اپوکسی پلی‌آمید}, abstract_fa = {در این مقاله از صفحات اکسید گرافن اصلاح سطحی شده توسط بنزایمیدازول به عنوان نانوذرات تقویت کننده پوشش اپوکسی استفاده شد. در این راستا، پس از سنتز اکسید گرافن و جذب فیزیکی مولکول‌های بنزایمیدازول بر روی آن، نانوصفحات اکسید گرافن اصلاح شده توسط بنزایمیدازول به همراه نانوذرات اصلاح نشده در بستر رزین اپوکسی به طور کامل پخش شدند. خواص فیزیکی مکانیکی پوشش های حاصل توسط آزمون DMTA و کشش مورد بررسی قرار گرفت. همچنین با استفاده از میکروسکوپ الکترونی روبشی، ریخت‌شناسی سطح شکست پوشش‌ها و چگونگی پخش نانوصفحات بررسی شد. نتایج نشان داد که مولکول‌های بنزایمیدازول به صورت موفقیت‌آمیزی با ایجاد پیوندهای غیر کووالانسی، سطح اکسیدگرافن را اصلاح نموده است. همچنین با افزودن نانوذرات اصلاح شده به پوشش، استحکام کششی نهایی، مدول یانگ، کرنش تا نقطه شکست و انرژی در نقطه شکست به ترتیب 81، 15، 310 و 207 % نسبت به پوشش اپوکسی بدون نانوذرات افزایش یافت. این بهبود خواص فیزیکی-مکانیکی پوشش به دلیل پخش بهتر نانوصفحات در پوشش و اتصال قوی‌تر مابین نانوصفحات با رزین است.}, keywords_fa = {پوشش اپوکسی پلی آمید,نانو صفحات اکسید گرافن,بنزایمیدازول,خواص فیزیکی-مکانیکی}, url = {https://jcst.icrc.ac.ir/article_81591.html}, eprint = {https://jcst.icrc.ac.ir/article_81591_13918f9175d76776bdf73c1cc013f53e.pdf} }